Topology
Adressing Table
Objectives
Configure hostnames and IP addresses on two Cisco Internetwork
Operating System (IOS) switches using the command-line interface (CLI).
· Use Cisco IOS commands to specify or limit access to the device configurations.
· Use IOS commands to save the running configuration.
· Configure two host devices with IP addresses.
· Verify connectivity between the two PC end devices.
· Use Cisco IOS commands to specify or limit access to the device configurations.
· Use IOS commands to save the running configuration.
· Configure two host devices with IP addresses.
· Verify connectivity between the two PC end devices.
Scenario
As a recently hired LAN technician, your network manager has asked you
to demonstrate your ability to configure a small LAN. Your tasks include
configuring initial settings on two switches using the Cisco IOS and
configuring IP address parameters on host devices to provide end-to-end
connectivity. You are to use two switches and two hosts/PCs on a cabled and
powered network.
Instructions
Configure the devices to fulfill the requirements below.
Requirements
·
Use a console connection to access each switch.
· Name Class-A and Class-B switches.
· Use the R4Xe3 password for all lines.
· Use the C4aJa secret password.
· Encrypt all clear text passwords.
· Configure an appropriate message-of-the-day (MOTD) banner.
· Configure addressing for all devices according to the Addressing Table.
· Save your configurations.
· Verify connectivity between all devices.
· Name Class-A and Class-B switches.
· Use the R4Xe3 password for all lines.
· Use the C4aJa secret password.
· Encrypt all clear text passwords.
· Configure an appropriate message-of-the-day (MOTD) banner.
· Configure addressing for all devices according to the Addressing Table.
· Save your configurations.
· Verify connectivity between all devices.
Class-A Router Configuration
Switch>en
Switch#conf t
S1(config)#line con 0
S1(config-line)#password R4Xe3
S1(config-line)#login
S1(config-line)#exit
S1(config)#
S1(config)#
S1(config)#line vty 0 15
S1(config-line)#password R4Xe3
S1(config-line)#login
S1(config-line)#exit
S1(config)#
S1(config)#int vlan 1
S1(config-if)#ip address 128.107.20.10 255.255.255.0
S1(config-if)#no shut
S1(config-if)#
%LINK-5-CHANGED: Interface Vlan1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
S1(config-if)#exit
S1(config)#banner motd #SWITCH S1#
S1(config)#hostname Class-A
Class-A(config)#service pass
Class-A(config)#exit
Class-A#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Switch#conf t
S1(config)#line con 0
S1(config-line)#password R4Xe3
S1(config-line)#login
S1(config-line)#exit
S1(config)#
S1(config)#
S1(config)#line vty 0 15
S1(config-line)#password R4Xe3
S1(config-line)#login
S1(config-line)#exit
S1(config)#
S1(config)#int vlan 1
S1(config-if)#ip address 128.107.20.10 255.255.255.0
S1(config-if)#no shut
S1(config-if)#
%LINK-5-CHANGED: Interface Vlan1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
S1(config-if)#exit
S1(config)#banner motd #SWITCH S1#
S1(config)#hostname Class-A
Class-A(config)#service pass
Class-A(config)#exit
Class-A#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Class-B Router Configuration
S2>en
S2#conf t
S2(config)#line con 0
S2(config-line)#password R4Xe3
S2(config-line)#login
S2(config-line)#exit
S2(config)#
S2(config)#
S2(config)#line vty 0 15
S2(config-line)#password R4Xe3
S2(config-line)#login
S2(config-line)#exit
S2(config)#
S2(config)#int vlan 1
S2(config-if)#ip address 128.107.20.15 255.255.255.0
S2(config-if)#no shut
S2(config-if)#
%LINK-5-CHANGED: Interface Vlan1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
S2(config-if)#exit
S2(config)#banner motd #SWITCH S2#
S2(config)#hostname Class-B
Class-B(config)#service pass
Class-B(config)#exit
Class-B#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
S2#conf t
S2(config)#line con 0
S2(config-line)#password R4Xe3
S2(config-line)#login
S2(config-line)#exit
S2(config)#
S2(config)#
S2(config)#line vty 0 15
S2(config-line)#password R4Xe3
S2(config-line)#login
S2(config-line)#exit
S2(config)#
S2(config)#int vlan 1
S2(config-if)#ip address 128.107.20.15 255.255.255.0
S2(config-if)#no shut
S2(config-if)#
%LINK-5-CHANGED: Interface Vlan1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
S2(config-if)#exit
S2(config)#banner motd #SWITCH S2#
S2(config)#hostname Class-B
Class-B(config)#service pass
Class-B(config)#exit
Class-B#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Student-1 PC Configuration
Student-2 PC Configuration
Verify Connectivity Between All Devices.
Ping From Student-1 To Student-2
- Follow Us on Twitter!
- "Join Us on Facebook!
- RSS
Contact